ELECTRICAL ENGINEERING PROJECT TOPICS FOR ENGINEERING STUDENTS-2013

• Embedded PIC MC based Electronic Trivector Meter
• Embedded PIC Microcontroller Based Power Multimeter
• Embedded PIC Microcontroller Based Motor Protection System
• Energy Management System for Pulse Output Meters
• AC Power line Monitoring motor generator application
• Speed Control of AC Motor
• Speed Control of DC Motor with Field and Armature Control
• DC Drive using IGBT
• AC Drive using IGBT
• Maximum Demand Indicator / Controller for Industries
• Power Factor Correction Using Multiple Capacitor Banks
• Electricity Billing Automation
• Prepaid Electricity Billing Automation
• Digital Tri Vector Meter
• Multiple starters with overload protection
• Multiple starters with overload protection with AI
• Multiple starters with overload protection with WAP
• Hybrid SCADA for Power station Substation Monitoring & Automation
• Embedded System based POSI-CAST controller for Dc-Dc Buck Convertor.
• Novel ZVT- PWM Converters with active snubbers
• Active resonant snubbers for high frequency PWM converters
• A ZVT-PWM Single stage PFC Converter with active snubber
• Electrical Station Variables Reader/Controller with True Graph and SCADA
• Electrical Station Variable Reader/Controller with True Graph
• Remote On/Off Controller for AC Motors with Parameter Monitoring
• Remote Switching System for home appliances
• Power Sharing of Transformers with WAP
• Power Sharing of Transformers with auto protection
• Computer Keyboard as a dual controller for switching Electrical devices
• Energy Saving In 1- Phase Induction Motor using A.C Chopper
• Harmonic Reduction using Capacitor Clamped Multilevel Inverter
• Harmonic Reduction using Diode Clamped Multilevel Inverter
• High Frequency Zero Voltage Switching Resonant Converter
• Integral Cycle Controlled Inverter fed Induction Motor Drive
• L-Type High Frequency Quasi Resonant Zero Current Switch
• Micro Controller based Transformer Protection Third Harmonic Auxiliary Commutated Current Source Inverter
• Thyristor Switched Capacitor scheme for fast changing industrial loads
• Two input full bridge DC-to-DC converter for selective Harmonic elimination.
• Two input Full Bridge Inverter with improved output waveform
• Closed Loop Speed Controller for DC Motor using Microcontroller
• Design of a Microcontroller-Controlled Personal Static Var Compensator (PSVC)
• Fuzzy Logic Based Faults Identification System for a Three-Phase Induction Motor PID controller for real time dc motor speed control
• Sensor field oriented control of 1 phase induction motor using microcontroller
• Programmable Single Phase Motor Overload Automatic Preventer
• Speed Control of DC / Induction Motor using PID / Fuzzy Controller
• Dual control of Electrical devices through Computer Keyboard and H/W
• Centralized Powerhouse Automation using WAP
• Slip Ring Induction motor Drive with slip Recovery using IGBT
• DC motor Starter using MOSFET
• Microcontroller Based Oil Temp/IND/CON
• 3 Phase AC Motor Drive using IGBT
• Two / Four Quadrent chopper in Indian Military
• Multi Channel Voltage Scanner with SCADA
• Micro controller based Position Control for Stepper Motor
• WEB-SCADA
• Speed Control of AC / DC / induction Motor with RF Technology
• Electric Power Generation using Footstep Method 
• Embedded Micro controller based Grid Synchronization 
• Energy Management Control System with WAP 
• Home Automation Using X-10 Protocol 
• Bi Directional VF Control of Single Phase AC Motors 
• Frequency Actuated Load Shedding with substation monitoring
• Management of sub-transmission and distribution system in power Systems 
• Mobile - Half Bridge Configuration Based High Voltage Generation of 10KVA_1KHZ 
• Vector Controlled Drive for Energy Saving in Air Conditioning system 
• High Performance AC Supply with Low Harmonic Distortion for multiphase AC Machines 
• Enhancement of power system performance using STATCOM
• Management of sub-transmission and distribution system in power 
• systems
• Remote data monitoring using WAP Information Gateway
• Vector Controlled Device For Energy Saving Air Conditioning System
• Fuzzy Logic Based Differential Relay For Power Transformer Protection 
• Single Phase to 3 Phase Converter For Driving 3 Phase Motor using Single Phase
• Embedded System based Automatic Furnace control for improvement of Hardness on materials.
• Distributed Multi area Power systems load flow monitoring
• SCADA Based Temperature Measurement & Control System
• SCADA for instrumentation with Artificial intelligence Control
• Intelligent Briefcase with digital code lock and shock generator during unauthorized access
• Digital Timer with Thumbwheel setting with On and Off delay type
• Digital Counter using Proximity Sensor
• Digital Energy meter using Embedded Controller
• Digital Energy meter with voice annunciation
• Digital RPM Indicator using Proximity or Magnetic Pick up
• Digital Frequency indicator
• Digital Voltmeter using Embedded System
• Digital Ammeter using Embedded System
• Cyclic Timer using Embedded system
• Remote Digital RPM Indicator using Proximity or Magnetic Pick up with SCADA

Simple Count Down Timer Using LCD

                   Countdown Timer Using LCD

A countdown timer is a down counter that counts from a specified time to zero. It is used in many devices such as washing machine, televisions, microwave ovens, etc. This countdown timer has three states: the running state where it counts down, the pause state where it displays the paused time and the reset state to set the countdown.

I have developed this count down timer as part of my another project.This  count down timer count from 99 to zero. This can be used as count down timer in hours or minutes or seconds by adjusting the delay value.For count down in minutes delay value will be 6000.Also the maximum value of count down can be change in program.The reset switch will reset the count down timer.Main parts of the project are microcontroller AT89C51and LCD,5v Regulated power supply.

Microcontroller AT89C51:

Microcontroller AT89C51 is at the heart of the circuit. It is a low power, high performance, 8-bit microcontroller with 4 kB of flash programmable and erasable read-only memory (PEROM) used as on-chip program memory, 128 bytes of RAM used as internal data memory, 32 individually programmable input/output (I/O) lines divided into four 8-bit ports, two 16-bit programmable timers/counters, a five-vector two-level interrupt architecture, on-chip oscillator and clock circuitry. A 11.0592MHz crystal (XTAL1) is used to provide basic clock frequency for the microcontroller. Capacitor C3 and resistor R3 form the power-on reset circuit, while push-to-on switch S20 is used for manual reset.

Liquid Crystal Display (LCD):

Liquid crystal display a type of display used in digital watches and many portable computers.LCD displays utilize two sheets of polarizing material with a liquid crystal solution between them. An electric current passed through the liquid causes the crystals to align so that light cannot pass through them. Each crystal, therefore, is like a shutter, either allowing light to pass through or blocking the light.

The liquid crystals can be manipulated through an applied electric voltage so that light is allowed to pass or is blocked. By carefully controlling where and what wavelength (color) of light is allowed to pass, the LCD monitor is able to display images. A back light provides LCD monitor’s brightness.Other advances have allowed LCD’s to greatly reduce liquid crystal cell response times. Response time is basically the amount of time it takes for a pixel to “change colors”. In reality response time is the amount of time it takes a liquid crystal cell to go from being active to inactive. Here the LCD is used at both the Transmitter as well as the receiver side. The input which we give to the microcontroller is displayed on the LCD of the transmitter side and the message sent is received at the receiver side which displays at the receiver end of the LCD and the corresponding operation is performed.

They make complicated equipment easier to operate. LCDs come in many shapes and sizes but the most common is the 16 character x 4 line display with no backlight. It requires only 11 connections – eight bits for data (which can be reduced to four if necessary) and three control lines (we have only used two here). It runs off a 5V DC supply and only needs about 1mA of current. The display contrast can be varied by changing the voltage into pin 3 of the display.

 Power Supply Unit

The power supply unit is used to provide constant 5 V dc supply to the peripherals. The 230 V ac is converted into 9 V ac by using a transformer and then a bridge rectifier rectifies it to a 9 V dc with ac ripples. This is then filtered by electrolytic capacitors used across the rectifier output. LM7805 regulator is employed to obtain a constant 5 V dc at the output.

 Count Down Timer Using LCD Program

#include<reg51.h>

#define cmdport P3

#define dataport P2

sbit rs = cmdport^0;  //register select pin

sbit rw = cmdport^1;  // read write pin

sbit e = cmdport^6;  //enable pin

void delay(unsigned int msec)  // Function to provide time delay in msec.

{

int i,j ;

for(i=0;i<msec;i++)

for(j=0;j<1275;j++);

}

void lcdcmd(unsigned char item)  //Function to send command to LCD

{

dataport = item;

rs= 0;

rw=0;

e=1;

delay(1);

e=0;

}

void lcddata(unsigned char disp)  //Function to send data to LCD

{

dataport = disp;

rs= 1;

rw=0;

e=1;

delay(1);

e=0;

}          

void main() 

{  

  while(1)

  {

    unsigned int i,s,test_final;

    lcdcmd(0x38);  // for using 8-bit 2 row mode of LCD

     delay(100);

      lcdcmd(0x0E);  // turn display ON for cursor blinking

       delay(100); 

        lcdcmd(0x80);

                    

                   delay(25);

          for(i=99;i>0;i--)

                     {     

                           lcdcmd(0x01);       

                                test_final=i;               

                  s=test_final/100;

                   test_final=test_final%100;

                   if(s!=0)

                                         {

                   lcddata(s+48);

                                         delay(250);

                                         }

                   else

                                         {                           

                            s=test_final/10;

                            test_final=test_final%10;

                            lcddata(s+48);

                             lcddata(test_final+48);

                            lcddata(0);

                                                                   delay(250);

                                                }                                   

                     }

   }

               

}